New Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone

Price:
US$72.00

Free Shipping

Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone











Holybro TekkoS 4 in 1 30A BLHeli_S ESC Built-in Current Sensor + Kakute F4 V2 Flight Controller OSD For RC Drone FPV Racing 

Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone
Holybro TekkoS 4 in 1 30A BLHeli_S ESC Current Sensor + Kakute F4 V2 Flight Controller For RC Drone


Items
 
Descriptions Features
Holybro Kakute F4 V2 Flight Controller
Item name: Kakute F4 V2
MCU: STM32F405RGT6 32-bit processor
IMU: ICM20689 (SPI)
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
5 hardware UARTS (UART1,3,4, 5, 6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
128 Mbit Dataflash chip for Blackbox logging.
Dimensions: 35x30x8mm (includes USB in height)
Mounting holes: Standard 30.5mm square to center of holes
Weight: 7g

Additional UART (UART 4) added to support serial camera communication such as to RunCam Split.
Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.
Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
Barometer sensor on board allows altitude hold mode.
I2C pad available for certain external sensors.
Supports Betaflight and Cleanflight.
Betaflight OSD.
Soft-mounting built in.
New high-performance / low-noise / high sensitivity IMU. 
ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
2 oz. copper PCB allows up to 120A maximum continuous current.
Dedicated bootloader button for easy firmware flashing.
Low-profile design fits into even very compact frames.
Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
Automatic voltage monitoring.
Filtered voltage output for clean, noise-free video. 
Supports BLHeli pass-through for easy ESC upgrade and configuration.
 

Holybro TekkoS 4 in 1 30A BLHeli_S ESC
Item name: TekkoS 4 in 1 30A BLHeli_S ESC
Con. Current: 30amp continuous draw per motor
Peak Current: 40amp
BEC: no 
Lipo input: 3-6S
MCU: BB21
Firmware: 48Mhz Runs BLHELI_S J_H_xx firmware
Mounting hole spacing: 30.5mm x 30.5mm 


BlHeli_S
D-Shot ready
Built in current sensor
Connector to flight controller
Current and voltage sent to flight controller
Easy install
High-quality components
Supports damped light
NO external capacitors needed
 

 
Package included:
1 x Kakute F4 V2 flight controller
2 x vibration-isolating foam
1 x FPC
1 x TekkoS 4-in-1 30A ESC
1 x 8pin JST 1mm pitch 70mm cable